Blower - Heavy Duty - Flangemount - 75mm - 12V - 4.0 m3/minute

High capacity output with quiet running Delrin rotor. Continuously rated motor maximum 1 hour with 50% duty cycle = 1 hour on then 1/2 hour off for cool down.

Features:

• Tough reinforced plastic housing
• Mount to any flat surface
• Slip-On inlet ducting connection
• Efficient high volume air flow
• Low current draw
• Corrosion-resistant materials throughout
• N.M.M.A Type accepted
• DC models comply with USCG electrical regulations of title 33, chapter I, part 183; subpart I and ISO 8846 MARINE for ignition protection
• DC models comply with ISO 9097 marine
• DC models conform with EN 50081-1 for suppression of electromagnetic interference
  
  Specifications:
  
  
• Air flow - 4.0 m3/minute (150cfm)
• Voltage - 12Vdc
• Amperage - 6.5
• Fuse size - 10A
• Weight - 2.3 kg (5 lb)
  
  Wiring for DC models : Use stranded copper wire. For lengths up to 25 feet (7.6m) from power source: Use 12 gauge wire for 12 Volt and 14 gauge wire for 24 Volt. Use larger wire for longer lengths. Use a 10 amp rated on-off switch in positive side of circuit (Model 44960-0003). Circuit must be protected with a fuse. Suggested fuse sizes are listed in the specifications table.
  
  Notice: blower should be mounted away from extreme heat (More than 54.4 Celsius) to prevent distortion of blower wheel or housing.
  
  For an exposed inlet, ventilator intake screen No. 34764-0000 provides a safe and attractive protection inlet. Note: This blower may also be mounted with inlet through bulkhead, using intake collar No. 34943-0000.
  
  Jabsco blowers are primarily intended for intermittent duty cycles such as evacuating fuel vapours from bilge areas. If desired, they may also be used for other general air circulation applications with longer duty cycles. However, when doing so, it should be noted that the maximum motor life is approximately 1000 hours. Therefore, the blower should only be used for applications if this length of service is acceptable.
  
  Operation: See following warning placard statement:
  
  The "WARNING" placard supplied with blower must be mounted adjacent to engine ignition switches (All locations) to comply with Title 33, Part 1834; Subpart K, USCG ventilation regulations.*
  
  *Additional warning placards are available from factory by requesting form 43003-0418.

Shipping and customer service

We use Australia Post Eparcel for shipping if goods within Australia. If you would like to use an alternative shipping method please Contact Us and we can discuss alternatives.

When you contact us, a real person will call you back! This is what separates us from our competitors. We are a real store on QLD's Gold Coast with over 30 years experience in boating and Customer care.

Returns policy

We have a 30-day return policy, which means you have 30 days after receiving your item to request a return.

To be eligible for a return, your item must be in the same condition that you received it, unworn or unused, with tags, and in its original packaging. You’ll also need the receipt or proof of purchase.

To start a return, you can contact us at chandlery@bosuns.com.au. If your return is accepted, we’ll send you a return shipping label, as well as instructions on how and where to send your package. Items sent back to us without first requesting a return will not be accepted.

You can always contact us for any return question at chandlery@bosuns.com.au.

PO Box 138, Main Beach QLD 4217

Southport Yacht Club, Macarthur Parade, Main Beach QLD 4217

Monday - Friday - 7.30am – 5pm
Saturday - 8am to 4pm
Sunday - 8am to 12noon

(07) 55 911 911 | Fax (07) 55 916 147

boats@bosuns.com.au